[. . . ] LAVASCIUGA LAVADORA-SECADORA MAQUINA DE LAVAR E SECAR WASHER-DRYER WIJ 1075 132999660 LIBRETTO ISTRUZIONI MANUAL DE USO MANUAL DE UTILIZAO INSTRUCTION BOOKLET YOUR NEW WASHER-DRYER This new washing machine, which is fitted with the Jet System, patented Zanussi, meets all modern needs for effective treatment of laundry with low water, energy and detergent consumption. Further savings are achieved by washing small loads of laundry, since water and electricity consumption is proportional to the quantity and type of laundry being washed. I The temperature selector dial will allow you to choose the most suitable temperature for your laundry. I I I I Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed. Use a "short programme" when washing lightly soiled laundry. [. . . ] Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Washing a maximum load makes the most efficient use of water and energy. For heavily soiled laundry, reduce the load size. Laundry weights The following weights are indicative: bathrobe napkin quilt cover sheet pillow case tablecloth towelling towel tea cloth night dress ladies' briefs man's work shirt man's shirt man's pyjamas blouse men's underpants 1200 g 100 g 700 g 500 g 200 g 250 g 200 g 100 g 200 g 100 g 600 g 200 g 500 g 100 g 100 g Temperatures 90 for normally soiled white cottons and linen (e. g. tea cloths, towels, tablecloths, sheets. . . ) for normally soiled, colour fast garments (e. g. shirts, night dresses, pyjamas. . . . ) in linen, cotton or synthetic fibres and for lightly soiled white cotton (e. g. net curtains), mixed laundry including synthetic fibres and woollens bearing the label pure new wool, machine washable, non-shrink. 60 (cold) 30-40 Removing stains Stubborn stains may not be removed by just water and detergent. For dried stains, soak overnight in water with a special detergent then rub in the soap and water. Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and dab the stain; treat several times. Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth. Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain. Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Remove any residual marks from white fabrics with bleach. Before loading the laundry Never wash whites and coloureds together. New coloured items may run in the first wash; they should therefore be washed separately the first time. Rub particularly soiled areas with a special detergent or detergent paste. Remove hooks or tie them up in a bag or net. Maximum loads Recommended loads are indicated in the programme charts. General rules: Cotton, linen: drum full but not too tightly packed; Synthetics: drum no more than half full; Delicate fabrics and woollens: drum no more than one third full. 80 Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse. Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. [. . . ] Frost precautions If the machine is installed in a place where the temperature could drop below 0C, proceed as follows: I Close the water tap and unscrew the water inlet hose from the tap. I Place the end of the outlet hose and that of the inlet hose in a bowl placed on the floor. I Screw the water inlet hose back on and put the outlet hose back in its place. By doing this, any water remaining in the machine is removed, avoiding the formation of ice and, consequently, breakage of the affected parts. [. . . ]